CCNA 4 - Final Exam (B)

1. Identify the factors that contribute to congestion on an Ethernet LAN. (Choose three.)
• improper placement of enterprise level servers
• addition of hosts to a physical segment
• replacement of hubs with workgroup switches
• increasing use of bandwidth intensive network applications
• migration to full-duplex Ethernet within the LAN
2. Which of the following are examples of TCP/IP application layer protocols? (Choose three.)
• a terminal emulation protocol that supports remote console connections with various network devices
• a protocol created by IBM that makes it easier for mainframes to connect to remote offices
• a protocol responsible for transporting electronic mail on TCP/IP networks and the Internet
• a protocol that controls the rate at which data is sent to another computer
• a protocol that exchanges network management information between a network device and a management console
3. Which of the following eliminates switching loops?
• hold-down timers
• poison reverse
• spanning tree protocol
• time to live
• split horizon protocol
4. The show cdp neighbors command is a very useful network troubleshooting tool. Using the output in the graphic, select the statements that are true. (Choose two.)
• CDP operates at the network layer of the OSI model.
• The output of this command displays information about directly connected Cisco devices only.
• The switch is attached to the SanJose1 FastEthernet0/21 interface.
• SanJose1 is running CDP version 12.0.
• SanJose1 has two fully operational, cdp-enabled Cisco switches directly connected to it.
• SanJose2 is a 2600 series router running several routed protocols
5. A network administrator can ping the Denver router, but gets a ‘Password Required but None Set’ message when trying to connect remotely via Telnet. Which command sequence must be applied to the Denver router to allow remote access?
• Router(config)# line console 0
Router(config-line)# login
Router(config-line)# password cisco
• Router(config)# line vty 0 4
Router(config-line)# login
Router(config-line)# password cisco
• Router(config)# line virtual terminal
Router(config-line)# enable login
Router(config-line)# password cisco
• Router(config)# line vty 0 4
Router(config-line)# enable secret
Router(config-line)# password cisco
Router(config)# enable secret cisco
Router(config)# enable cisco
6. Which of the following is associated with link-state routing protocols?
• low processor overhead
• poison reverse
• routing loops
• split horizon
• shortest-path first calculations
7. A router does not load its configuration after a power failure. After running the show startup-configuration command, the adminstrator finds that the original configuration is intact. What is the cause of this problem?
• The configuration register is set for 0×2100.
• The configuration register is set for 0×2101.
• The configuration register is set for 0×2102.
• The configuration register is set for 0×2142.
• Boot system commands are not configured.
• Flash memory is empty causing the router to bypass the configuration in NVRAM
• Nederst på formularen
8. Which commands are used to verify the content and placement of access control lists? (Choose three.)
• show ip interface
• show ip route
• show processes
• show running-config
• show cdp neighbor
• show access-lists
9. Which of the following are required when creating a standard access control list? (Choose two.)
• destination address and wildcard mask
• source address and wildcard mask
• subnet mask and wildcard mask
• access list number between 100 and 199 or 2000 and 2699
• access list number between 1 and 99 or 1300 to 1999
10. Which of the following are keywords that can be used in an access control list to replace a dotted decimal wildcard mask? (Choose two.)
• most
• host
• all
• any
• some
• sum
11. Refer to the diagram. All ports on Switch A are in the Sales VLAN and all ports on Switch B are in the Accounting VLAN. How many broadcast domains and how many collision domains are shown? (Choose two).
• 3 collision domains
• 3 broadcast domains
• 5 broadcast domains
• 9 collision domains
• 10 collision domains
• 13 collision domains
12. Refer to the graphic. Using the most efficient IP addressing scheme and VLSM, which address can be configured on one of the serial interfaces?
• 192.168.16.63/27
• 192.168.16.158/27
• 192.168.16.192/27
• 192.168.16.113/30
• 192.168.16.145/30
• 192.168.16.193/30
13. What is the purpose of the Spanning Tree Protocol (STP)?
• prevents Layer 2 loops
• prevents routing loops on a router
• creates smaller collision domains
• creates smaller broadcast domains
• allows Cisco devices to exchange routing table updates
14. What is the purpose of a loopback address when using the OSPF routing protocol?
• activates the OSPF neighboring process
• ensures a persistent router ID for the OSPF process
• provides a backdoor for connectivity during the convergence process
• streamlines and speeds up the convergence process
15. Which statement is true regarding states of the IEEE 802.1d Spanning Tree Protocol?
• Ports are manually configured to be in the forwarding state.
• Ports listen and learn before going into the forwarding state.
• Ports must be blocked before they can be placed in the disabled state.
• It takes 15 seconds for a port to go from blocking to forwarding
16. Which sequence of commands is used to configure a loopback address on a router?
• Router1(config)# interface loopback 1
Router1(config-if)# ip address 192.168.1.1
Router1(config)# interface serial 0/0
• Router1(config-if)# loopback 1
Router1(config-if)# ip address 192.168.1.1
Router1(config)# interface serial 0/0
• Router1(config-if)# loopback 1
Router1(config-if)# ip address 192.168.1.1 255.255.255.0
• Router1(config)# interface loopback 1
Router1(config-if)# ip address 192.168.1.1 255.255.255.255
17. Which routing protocols are classful and do not support VLSM? (Choose two.)
• EIGRP
• OSPF
• RIP v1
• RIP v2
• IGRP
18. Refer to the graphic. Two switches are connected together through a trunk port. SW2 displays the message shown. Which of the following will solve the duplex mismatch?
• SW1(config)# interface fastethernet 0/1
SW1(config-if)# duplex full
• SW1(config)# interface fastethernet 0/1
SW1(config-if)# full-duplex
• SW2(config)# interface fastethernet 0/1
SW2(config-if)# duplex full
• SW2(config)# interface fastethernet 0/1
SW2(config-if)# full-duplex
19. Refer to the graphic. Two routers have been configured to use EIGRP. Packets are not being forwarded between the two routers. What could be the problem?
• EIGRP does not support VLSM.
• The routers were not configured to monitor neighbor adjacency changes.
• The default bandwidth was used on the routers.
• An incorrect IP address was configured on a router interface.
20. According to the the provided router output, which of the following statements is true regarding PPP operation?
• Only the link-establishment phase completed successfully.
• Only the network-layer phase completed successfully.
• Neither the link-establishment phase nor the the network-layer phase completed successfully.
• Both the link-establishment and network-layer phase completed successfully
21. Frame Relay is configured over a point-to-point connection between two routers. The output of the show frame-relay pvc command indicates that the status of this PVC is inactive. Which of the following devices could be the source of the problem? (Choose two.)
• local router
• local Frame Relay switch
• remote router
• remote Frame Relay switch
• R3 has the following configuration:
• R3# show running-config
• –some output text omitted–
• interface serial0/0
• bandwidth 128
• ip address 192.168.11.2 255.255.255.0
• encapsulation frame-relay
• frame-relay map ip 192.168.11.2 30 broadcast
22. After the command R3# debug frame-relay packet is executed, a ping is issued from R3 to R1 but is unsuccessful. Based on the output of the debug command shown in the graphic and the router configuration, what might be problem?
• No clock rate assigned.
• There is an incorrect DLCI number in the map statement.
• An incorrect IP address exists in the map statement.
• The encapsulation command is missing the broadcast keyword
23. Which statements are true regarding the Frame Relay LMI? (Choose three.)
• The LMI provides a virtual circuit (VC) status mechanism.
• The LMI type must always be manually configured.
• The available LMI types are NI1, DMS100 and 5ESS.
• The LMI types supported by Cisco routers are CISCO and IETF.
• The LMI type configured on the router must match the one used on the Frame Relay switch.
• The LMI uses reserved DLCIs to exchange messages between the DTE and DCE

24. Which statement describes the process that occurs in Network Address Translation (NAT) overloading?
• Multiple private IP addresses are mapped to one public IP address.
• The number of usable addresses assigned to a company is divided into smaller manageable groups.
• A pool of IP addresses are mapped to one or more MAC addresses.
• The router acts as a DHCP server and assigns multiple public IP addresses for each private IP address configured
25. Which two statements are true about the committed information rate on a Frame Relay link? (Choose two.)
• The sum of the CIRs for all PVCs must be less than the port speed.
• The sum of the CIRs for all PVCs must equal the port speed.
• The sum of the CIRs for all PVCs can be greater than the port speed.
• The DE bit will be set on frames that are transmitted in excess of the CIR.
• Frames that are transmitted at greater than the CIR will be discarded at the source.
• It is impossible to transmit frames at a rate in excess of the CIR
26. Which of the following commands would be used to troubleshoot the processing of call control functions such as call setup, signaling, and termination?
• show interface bri0/0
• show isdn active
• debug isdn q921
• debug isdn q931
• debug ppp negotiation
• debug ppp authentication
27. Which of the following statements are true regarding PPP? (Choose three.)
• PPP can use synchronous and asynchronous physical media.
• PPP can only be used between two Cisco devices.
• PPP carries packets from several network layer protocols in LCPs.
• PPP uses LCPs to establish, configure, and test the data link connection.
• PPP uses LCPs to agree on format options such as authentication, compression, and error detection
28. A network administrator is evaluating authentication protocols for a PPP link. Which of the following reasons might lead to the selection of CHAP over PAP as the authentication protocol? (Choose three.)
• establishes identities with a two-way handshake
• uses a three-way authentication periodically during the session to reconfirm identities
• control by the remote host of the frequency and timing of login events
• transmits login information in encrypted format
• uses an unpredictable variable challenge value to prevent playback attacks
• makes authorized network administrator intervention a requirement to establish each session
29. Why are static routes often used with ISDN DDR?
• They are more stable than dynamic routing protocols.
• They are more accurate than dynamic routing protocols because they are put in by a network administrator.
• They are easier to modify when a faster technology is installed.
• They prevent the unnecessary activation of the link
30. Assuming that four bits have been borrowed to make subnets, identify the subnet network addresses. (Choose three.)
• 192.168.14.8
• 192.168.14.16
• 192.168.14.24
• 192.168.14.32
• 192.168.14.148
• 192.168.14.208
31. A switch can be configured for three different forwarding modes based on how much of a frame is received before the forwarding process begins. Each of the numbered arrows in the accompanying graphic signifies the point in a frame where a particular forwarding mode will begin. Which one of the following groups reflects the sequence of forwarding modes signified by the numbered arrows?
• 1) fast forward
• 2) fragment free
• 3) store-and-forward
• 1) store-and-forward
2) fragment free
3) fast forward
• 1) fragment free
2) fast forward
3) store-and-forward
• 1) fast forward
2) store-and-forward
3) fragment free
32. Which of the following commands will display a communication message on a router before the router prompt is shown?
• banner motd * Property of TLC. UNAUTHORIZED USERS WILL BE PROSECUTED TO THE FULL EXTENT OF THE LAW. *
• message Property of TLC. UNAUTHORIZED USERS WILL BE PROSECUTED TO THE FULL EXTENT OF THE LAW.
• banner * Property of TLC. UNAUTHORIZED USERS WILL BE PROSECUTED TO THE FULL EXTENT OF THE LAW. *
• hostname (Property of TLC. UNAUTHORIZED USERS WILL BE PROSECUTED TO THE FULL EXTENT OF THE LAW.)
• Øverst på formularen
33. A router needs to be added to OSPF area 0. Which commands should be used to enable OSPF on the router? (Choose two.)
• RouterA(config)# router ospf
• RouterA(config)# router ospf 1
• RouterA(config-router)# network 192.168.2.0 0.0.0.255 0
• RouterA(config-router)# network 192.168.2.0 0.0.0.255 area 0
• RouterA(config-router)# network 192.168.2.0 255.255.255.0 0
34. Refer to the graphic. Which of the following commands will configure router A for OSPF?
• router ospf 1
network 192.168.10.0
• router ospf 1
network 192.168.10.64 0.0.0.63 area 0
network 192.168.10.192 0.0.0.3 area 0
• router ospf 1
network 192.168.10.64 255.255.255.192
network 192.168.10.192 255.255.255.252
• router ospf 1
network 192.168.10.0 area 0
35. Which of the following protocols would exchange information between routers to share network addresses and their metrics?
• TCP
• RIP
• CSMA/CD
• Ethernet
36. Which ISDN device can be directly connected to a two-wire local loop in a North American city?
• a router with a serial interface
• a router with an S/T interface
• a router with a U interface
• an ISDN terminal adapter
37. The output of the show ip interfaces brief command indicates that Serial0 is up but the line protocol is down. Which of the following are possible causes for the line protocol being in the down state? (Choose two.)
• The clock rate is not set on the DTE.
• An incorrect default gateway is set on the router.
• A network is missing from the routing protocol configuration.
• The encapsulation on the Serial0 interface is incorrect.
• Keepalives are not being sent by the remote device
38. Which of the following is a characteristics of TCP? (Choose two.)
• data transport reliability
• best path determination
• establishing, maintaining, and terminating virtual circuits
• encapsulation of packets in a data frame with source and destination MAC addresses
• best-effort datagram delivery
39. Which statement is true regarding the command ip route 192.168.7.24 255.255.255.248 192.168.7.9? (Choose two.)
• A packet destined for host 192.168.7.30 will be forwarded to address 192.168.7.9.
• 192.168.7.9 is the destination network for this route.
• 192.168.7.24 is the next-hop router in this command.
• This command is issued from the interface configuration mode.
• This command is used to define a static route
40. Which of the following application layer protocols use TCP? (Choose three.)
• SMTP
• FTP
• SNMP
• HTTP
• TFTP
• DHCP
41. Which terms refer to Frame Relay congestion management mechanisms? (Choose three.)
• BECN
• DLCI
• DE
• FECN
• LMI
• Inverse ARP
42. Which of the following router commands will verify that a path exists to a destination network?
• Router# show ip interfaces brief
• Router# show ip route
• Router# show cdp neighbors
• Router# show running-config
• Router# show protocols
43. When EIGRP is configured on a router, which table of DUAL information is used to calculate the best route to each destination router?
• router table
• topology table
• DUAL table
• CAM table
• ARP table
44. Refer to the graphic. Routers A and B have EIGRP configured and automatic summarization has been disabled on both routers. Which of the following commands is used on router A to summarize the attached routes, and to which interface is this command applied? (Choose two)
• ip summary-address eigrp 1 192.168.10.64 255.255.255.192
• ip area-range eigrp 1 192.168.10.80 255.255.255.224
• summary-address 192.168.10.80 0.0.0.31
• ip summary-address eigrp 1 192.168.10.64 0.0.0.63
• serial interface on router A
• serial interface on router B
45. A router with two LAN interfaces, two WAN interfaces, and two loopback interfaces configured is operating with OSPF as its routing protocol. What is used by the OSPF process to assign the router ID?
• the IP address of the interface configured with priority 0
• the OSPF area ID configured on the interface with the highest IP address
• the loopback with the highest IP address configured
• the highest IP address on the LAN interfaces
• the highest IP address configured on the WAN interfaces
46. Given the IP address and subnet mask of 172.16.134.56 255.255.255.224, on which subnetwork does this address reside?
• 172.0.0.0
• 172.16.134.0
• 172.16.134.32
• 172.16.134.48
• 172.16.134.47
• 172.16.134.63
47. Which commands show when the last IGRP routing update was received? (Choose two.)
• Router# show ip protocols
• Router# show version
• Router# show interfaces
• Router# show ip updates
• Router# show ip route
48. When using access control lists to filter traffic, which of the following is used to track multiple sessions occurring between hosts?
• IP addresses
• subnet masks
• port numbers
• routed protocols
• routing protocols
• interfaces
49. Given the IP address and subnet mask of 172.16.134.64 255.255.255.224, which of the following would describe this address?
• This is a useable host address.
• This is a broadcast address.
• This is a network address.
• This is not a valid address
50. The company network shown in the drawing has to be subnetted. The company has leased the Class C IP address of 200.1.2.0. Which of the following network addresses and masks would be appropriate for one of the subnetworks?
• 200.1.2.96 255.255.255.192
• 200.1.2.160 255.255.255.224
• 200.1.2.80 255.255.255.224
• 200.1.2.32 255.255.255.240 Read more..!

CCNA 4 - Final Exam (C)

1. Which of the following describes the roles of devices in a WAN? (Choose three.)
• A CSU/DSU terminates a digital local loop.
• A modem terminates a digital local loop.
• A CSU/DSU terminates an analog local loop.
• A modem terminates an analog local loop.
• A router is commonly considered a DTE device.
• A router is commonly considered a DCE device.
2. What value in the address field of a Frame Relay header identifies the destination of the frame?
• CIR
• DE
• DLCI
• ISDN
• FRAD
• PVC
3. The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue explains why the link is unable to establish a PPP session?
• The IP addresses must be on different subnets.
• The usernames are misconfigured.
• The passwords must be different for the CHAP authentication.
• The clock rate must be 56000.
• The clock rate is configured on the wrong end of the link.
• Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
4. The output of the show interfaces serial 0/0 command for a frame-relay connection indicates that the serial line is up but the line protocol is down. What are possible causes for this? (Choose two.)
• There is an LMI-type mismatch between the Frame Relay switch and the router.
• There is no clock present on the serial interface.
• The interface is shut down.
• RARP is not functioning on the router.
• The cable is disconnected.
5. Which statements are correct about the point in the network where the responsibility of the service provider ends? (Choose three.)
• The International point is on the customer side of the network terminating unit(NTU).
• The United States point is at the interface of the customer-provided equipment and the local loop.
• The responsibility for this point is controlled by IANA.
• The point is called the demarcation point.
• The point is typically located at the service provider’s central office.
• The point is located between the customer’s local area networks.
6. While prototyping an internetwork in the corporate lab, a network administrator is testing a serial link between serial 0/0 interfaces on two routers. The labels on the serial cable ends have been damaged and are unreadable. What command can be issued to determine which router is connected to the DCE cable end?
• show interfaces serial 0/0
• show version
• show controllers serial 0/0
• show protocols serial 0/0
• show status serial 0/0
7. A network technician determines DHCP clients are not working properly. The clients are receiving IP configuration information from a DHCP server configured on the router but cannot access the Internet. From the output in the graphic, what is the most likely problem?
• The DHCP server service is not enabled.
• The inside interface for DCHP is not defined.
• The DHCP pool is not bound to the interface.
• The pool does not have a default router defined for the clients.
• All the host addresses have been excluded from the DHCP pool.
8. A technician enters the interface serial 0/0.1 multipoint command when configuring a router. What effect will the multipoint keyword have in this configuration? (Choose two.)
• Split-horizon issues will need to be resolved for this network if RIP is the routing protocol.
• A subinterface will be defined for each PVC.
• All the participating interfaces of remote routers will be configured in the same subnet.
• A single DLCI will be used to define all the PVCs to the remote routers.
• An IP address will need to be configured on the main interface.
9. When configuring a Frame Relay connection, when should a static Frame Relay map be used? (Choose two.)
• when the remote router is a non-Cisco router
• when the remote router does not support Inverse ARP
• when the local router is using IOS Release 11.1 or earlier
• when broadcast traffic and multicast traffic over the PVC must be controlled
• when globally significant rather than locally significant DLCIs are being used
10. Which router command would be used to associate a Layer 2 address with the corresponding Layer 3 address in the internetwork in the diagram?
• RouterA(config-if)#frame-relay pvc 100 192.168.15.2
• RouterA(config-if)#dialer-map ip 192.168.15.1 100 broadcast
• RouterA(config-if)#frame-relay map ip 192.168.15.2 100 broadcast
• RouterA (config-if)#dialer-map 192.168.15.1 101 serial 0 broadcast
• RouterA (config-if)#frame-relay dlci 101 192.168.15.1 broadcast
• RouterA (config-if)#dialer-map 192.168.15.1 inverse-arp broadcast
11. Which of the following ISDN protocols is responsible for call setup and call teardown?
• ITU-T Q.921
• ITU-T Q.931
• ITU-T I.430
• ITU-T I.431
12. What are two ways to resolve split-horizon issues in a Frame Relay network? (Choose two.)
• create a full-mesh topology
• disable Inverse ARP
• use point-to-point subinterfaces
• use multipoint subinterfaces
• remove the broadcast keyword from the frame-relay map command
13. What is the purpose of the command marked with an arrow shown in the partial configuration output of a Cisco 806 broadband router?
• defines which addresses are allowed out of the router
• defines which addresses are allowed into the router
• defines which addresses can be translated
• defines which addresses are assigned to a NAT pool
14. A system administrator is unable to ping the Serial0/0 interface of RouterB from RouterA. During the troubleshooting process, the following facts are established:
- IP addressing and subnet masks are correct.
- RouterA is a Cisco router and RouterB is a router from another vendor.
- RouterA is configured with the default encapsulation.
- The serial interfaces on both routers are up.
- The protocol is down on the serial interfaces of both routers.
What should the administrator do to solve the problem?
• Add a clock rate on RouterA.
• Enable the serial interface on RouterB.
• Change the encapsulation on both routers to PPP.
• Connect the serial cable to the correct interface on RouterB.
• Use the correct serial cable to attach the CSU/DSU to RouterB.
15. An ISDN circuit from a branch office is remaining connected to the regional office. A network administrator determines a user has initiated a continuous ping from a desktop computer to the regional office. Which configuration change would allow the ISDN circuit to disconnect during any attempts to ping, while otherwise functioning properly?
• change DDR from legacy to dialer profiles
• remove the dialer list statement from the configuration
• change the dialer list to exclude ICMP as interesting
• disable inverse ARP
16. Below is a list of DDR steps. Which of the following identifies the proper order of DDR?
1 - dial number is looked up
2 - interesting traffic triggers DDR
3 - route to destination is determined
4 - call is made
• 1,2,3,4
• 1,3,2,4
• 2,3,1,4
• 2,1,3,4
• 3,2,1,4
• 3,1,2,4
17. Which protocol should be chosen to support WAN connectivity in a multi-vendor system and provide strong security through authentication?
• NAT with DHCP
• Frame Relay
• HDLC with encryption
• HDLC with CHAP
• PPP with PAP
• PPP with CHAP
18. Which of the following are valid steps for a basic ISDN BRI configuration? (Choose two.)
• create subinterfaces
• define the LMI type
• set the SPIDs if required by the ISDN switch
• set the interface DLCI
• set the switch type
• specify the encapsulation as either Cisco or IETF
19. A branch office reports excessive connect time charges for an ISDN circuit used to connect to the regional office. Upon investigation of this issue, it is discovered that when an ISDN connection is initiated to the regional office it remains connected for an excessive amount of time. Which of the following configuration changes could be made to DDR on the router to reduce these connect time charges?
• use PPP multilink
• lower idle timer setting
• use CHAP authentication
• change DDR from legacy to dialer profiles
20. A network administrator is having difficulty in establishing a serial link between a Cisco router and a router from another vendor. Both routers are configured for HDLC encapsulation. Which statements are true regarding this configuration? (Choose two.)
• The Cisco HDLC frame uses a proprietary “Type” field that may not be compatible with equipment of other vendors.
• HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
• PPP encapsulation is recommended for serial links between equipment from multiple vendors.
• Usernames must be configured at both ends of the HDLC serial link.
• The HDLC vendor type must be enabled on the Cisco router.
• There is a mismatch in the HDLC authentication password configurations.
21. Given the partial router configuration in the graphic, why does the workstation with the IP address 192.168.1.153/28 fail to access the Internet? (Choose two.)
• The NAT inside interfaces are not configured properly.
• The NAT outside interface is not configured properly.
• The router is not properly configured to use the access control list for NAT.
• The NAT pool is not properly configured to use routable outside addresses.
• The access control list does not include the IP address 192.168.1.153/28 to access the Internet.
22. The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue will prevent IP traffic from crossing this link?
• The passwords must be different for the CHAP authentication.
• The usernames are misconfigured.
• The clock rate must be 56000.
• The clock rate is configured on the wrong end of the link.
• The IP addresses must be on the same subnet.
• Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
23. What causes a DDR call to be placed?
• dial string
• DLCI
• idle time out
• interesting traffic
• PVC
24. Which two layers of the OSI model are described by WAN standards?
• Application Layer, Physical Layer
• Data Link Layer, Physical Layer
• Data Link Layer, Transport Layer
• Physical Layer, Network Layer
25. A technician is testing RouterA in the graphic. What is the condition of the circuit?
• The routers are configured for different encapsulations.
• The clock rate is not properly configured on the routers.
• The circuit from WAN provider has failed.
• Authentication is not properly configured on the routers.
• The circuit is functioning properly.
26. A network administrator must provide WAN connectivity between a central office and three remote sites: Orlando, Atlanta, and Phoenix. The Orlando and Atlanta remote offices receive sales orders and transmit shipping confirmations to the Central office consistently throughout the day. The Phoenix remote office consists of one salesperson traveling through the southwest territory. The salesperson occasionally needs to connect to the Central office for e-mail access. How should the network administrator connect the remote sites to the Central office? (Choose two.)
• Connect to the Atlanta and Orlando remote offices with Frame Relay connections.
• Connect to the Atlanta and Orlando remote offices with ISDN connections.
• Connect to the Atlanta and Orlando remote offices with POTS dial-up connections.
• Connect to the Phoenix remote office with a Frame Relay connection.
• Connect to the Phoenix remote office with a POTS dial-up connection.
27. When a Frame Relay switch detects an excessive buildup of frames in its queue, which of the following may occur? (Choose two.)
• Frames with the DE bit set are dropped from the switch queue.
• Frames with the FECN and BECN bits set are dropped from the switch queue.
• Frames in excess of the CIR are not accepted by the switch.
• The switch sets the FECN bit on all frames it places on the congested link and sets the BECN bit on all frames it receives on the congested link.
• The switch sets the FECN bit on all frames it receives on the congested link and sets the BECN bit on all frames it places on the congested link.
28. A system administrator is troubleshooting a connectivity issue between two routers in a new installation. The administrator enters the debug ppp authentication command on the WHSE router. The graphic shows a part of the output received. From this output, what is the most likely cause of this connectivity issue?
• There is not a route to the remote router.
• The ISDN circuit on the remote router has failed.
• The username/password was not properly configured on the WHSE router.
• The remote router has a different authentication protocol configured.
29. What does the output of the show frame-relay map command shown below represent? (Choose two.)
• Serial 0 (up): ip 172.30.151.4 dlci 122, dynamic, broadcast, status defined, active
• 172.30.151.4 represents the IP address of the remote router.
• 172.30.151.4 represents the IP address of the local serial interface.
• DLCI 122 represents the interface of the remote router.
• broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC.
• dynamic indicates that a dynamic routing protocol is enabled for this connection.
• active indicates that the ARP process is working.
30. What does the status inactive indicate in the output of the show frame-relay pvc command?
• The DLCI is programmed in the switch but is not usable.
• The DLCI was formerly programmed in the switch but is no longer there.
• The DLCI is usable but has little activity.
• The DLCI has been renamed for that PVC.
31. Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
• 192.168.146.0/22
• 172.10.25.0/16
• 172.31.0.0/16
• 20.0.0.0/8
• 10.172.92.8/29
32. After configuring a dialup ISDN circuit, a network associate begins testing the dialup connection. When attempting to ping a host on the remote network, the local router does not attempt to dial the remote access server. Which of the following are possible errors in this configuration? (Choose three.)
• PPP authentication is not properly configured.
• No dialer map is configured.
• The ISDN circuit connected to the remote access server is busy.
• No interesting traffic is defined.
• No route is determined to the remote network.
• A wrong number is configured in the dial string.
33. Two routers are connected through a Frame Relay, point-to-point PVC. The remote router is from a vendor other than Cisco. Which interface command is required to configure the link between the Cisco router and the other router?
• frame-relay pvc multipoint
• frame-relay pvc point-to-point
• encapsulation frame-relay cisco
• encapsulation frame-relay ietf
• frame-relay lmi-type ansi
34. Which circuit-switched WAN technology is often used to provide a backup for a leased line and additional capacity during peak usage times?
• X.25
• DSL
• ISDN
• cable modem
35. After the ISDN BRI interface is configured, which command can be used to verify that the router is communicating correctly with the ISDN switch?
• show dialer
• show isdn status
• show interfaces bri0/0:1
• show interfaces serial0/0.1
36. A system administrator needs to configure the regional office with ISDN for DDR connections to three remote sites. Each remote site requires different IP subnets, different encapsulations, and different authentication methods. The sites will not be connected at the same time. The company would like to accomplish this in the most cost effective manner. What method can the system administrator use to accomplish this task using the fewest B channels?
• Install and configure a PRI.
• Install and configure a BRI interface with separate SPIDs for each remote site.
• Install and configure a BRI with multiple switch types in global configuration.
• Install and configure a BRI using dialer profiles.
• Install and configure a separate BRI for each remote site.
37. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
• Configure static NAT for all ten users.
• Configure dynamic NAT for ten users.
• Configure dynamic NAT with PAT.
• Configure DHCP and static NAT.
• What the administrator wants to do cannot be done.
38. Which of the following are characteristics of Frame Relay? (Choose two.)
• circuit-switched
• connection oriented
• OSI Layer 3
• packet-switched
• reliable
39. Which of the following is the order for the three phases of establishing a PPP serial link with authentication?
• authentication, link-establishment, network layer protocols
• authentication, network layer protocols, link-establishment
• network layer protocols, link-establishment, authentication
• network layer protocols, authentication, link-establishment
• link-establishment, authentication, network layer protocols
• link-establishment, network layer protocols, authentication Read more..!

CCNA Lab: Copy to TFTP Server

Items of practical training certificates Cisco CCNA: Copy to TFTP Server

Start practicing: Link here Read more..!